Carburetor to intake bolt set
A-Ford 1928-31 OEM: A-9510-MB
Carburetor bolt. Zenith. A-Ford
The long bolt that joins the bowl of the Zenith carburator to the top of the carburetor A-Ford 1928-31 A-9512
Gasket manifold carburetor. A-Ford
A9447
Tillotson Carburetor Kit. A-Ford
Complete Set of jets, needles, & float valve to rebuild the original Tillotson Carburetor. All the needles, jets, and float valve for the Tillotson carb. This kit only works on pot metal Tillotson carbs with the bowl that is held on with 3 screw...
Tillotson Carburetor gasket set. A-Ford
Drain plug. A-Ford
Cadmium drain plug for Tillotson and Zenith 1930 - 1931
Tillotson Carburetor Choke Plate
A-Ford 1928-31A9611
Carburetor Idle Mixture Screw, Tillotson
Screw with cap and stainless spring for Tillotson carburetorA-Ford 1928-31A9577T
Main jet for the Tillotson Carburetor
A-Ford 1928-31A9534T
Tillotson Carb Inlet Needle & Seat
Brass Seat, Stainless Needle, and Fiber Gasket included.A-Ford 1928-31A9533T
Float valve Tillotson carburetor
Replaces original needle and seat. Uses 2 balls to shut off gas flow.A-Ford 1928-31A9564GJT
Float for the Tillotson carburetor.
A-Ford 1928-31A9550T
Tillotson Carburetor Choke Shaft
A-Ford 1928-31A9610
Cadmium plated strainer for Zenith carburetor
A-Ford 30-31A9559C
Carburetor Air Maze with steel Filter - Zenith. A-Ford
Zenith Carburetor Kit - Model A Ford
Complete Set of jets, needles, & float valve to rebuild original Zenith carb. Incl. gasket Sets.A-Ford 1928-31A9595Z
Zenith carburetor gasket set. A-Ford
Marvel Carburateur pakking set A-Ford
Carburetor float
Known as the B-2 style carburetor float, used on 1932-34 Zenith carburetors. The earlier style was more barrel shaped B-9550
B-Ford carburetor kit
Carburetor rebuilding kit for the 1932-34 Zenith carburetor. The float valve (B-9564) is not included with the carburetor kit and must be purchased seperately if it needs to be replaced. B-Ford 1932-34 OEM: B-9595
B Ford Carburetor Gasket Kit - Model A Ford
Zenith 1932 B Carburetor Kit.
Carburetor Throttle Shaft / Lever - Zenith
Std. Diameter 9/32"". If shaft & lever are worn replace it with this new standard one. .281 Diameter.
Carburetor Throttle Shaft / Lever. Oversize - Zenith
O.S. Diameter 19/64"". If shaft & lever are worn replace with this new oversized one. .294 DiameterA-Ford 1928-31
Carburetor Throttle Shaft Bushings - Zenith
Carburetor housings get worn where the throttle shaft goes through. These knurled bushings bring holes back to size. Some machine work to be done.A-Ford 1928-31A9581BU
Carburetor Idle Mixture Screw
Screw with cap and stainless spring.A-Ford 1930-31A9577BMB
Carburetor Idle Mixture Screw
Screw with cap and stainless spring. The 28 to Mid 1930 are brass with large heads.
Zenith Passage Plugs
New Set needed when you clean the internal channels of a Zenith Carburetor. Drill out the old ones, then peen new ones in placeA-Ford 1928-31A9576
Carburetor Compensator Jet. A-Ford
A-Ford 1928-31A9575
Brass strainer for Zenith carburetor
A-Ford 1928-30A9559B
Carburetor Fuel Level Gauge. Zenith
Remove the guesswork on your Zenith carburetor. This set shows the gas level in carb. bowl, so float level can be adjusted. Should be 5/8 inch below gasket.A-Ford 1928-31
