Model A Ford Cowl Rubber Shim Set - 6 Pieces - 1/8 Thick Use these under the cowl to align the doors and hood. A-Ford 1928-31 OEM: A-5002-P

This is used to take up the space caused by wear on the radius rod ball. Use ONLY with the original style stamped steel ball socket only, not the replacement style with a rubber ball. Grease prior to installing. May require one or two.

Mounted on the outside of the fire wall on the passenger side of all Model A carsA-Ford 1928-31A18650

Rivet set, Every rivet needed on the A-Ford

Radiator emblem A-Ford 1928-30

The 31's used this stainless emblem that had the lettering stamped in. The lettering is painted black as original OEM: A-8212-B

Ford 1928-31

Rear view mirror with beveled mirror glass Fits closed cab Ford 1927-31

This style was used on all 1930-31 closed cars.  Chrome. U.S. made with the correct bevel on the glass A-Ford 1930-31 OEM: A-17681-BCC

Fits 1930-31 open car, clamps to top of windshield frame tubing. U.S. made with correct bevel on glass. Polished Stainless Steel OEM: A-17681-BOS

Clamps to the tubing of the windschield frame Mirror:  beveled edge  A-Ford :  Roadsters, Phaetons, en Roadster Pickup Trucks. OEM: A-17681-AOB

Mirror glass is 3-1/2" diameter. These clamp onto the glass of the accessory windwings

Mirror glass is 3-1/2" diameter. these clamp onto the glass of the accessory windwingsBrass version

Mirror diameter 12.5 cm. cast iron support 16.5 cm long. Mounts to a (wooden) support of a car of truck

A chrome bracket with a highly polished stainless mirror head. Head adjusts in and out to your liking! Mount pin included, works on all 1928-31 closed cars, except slant windshield 4-doors

A-Ford 1930-31 Similar to our H10182  hinge mirror except this one has an offset arm. 43.18 mm is the width where it slips over the top and bottom of the hinge. Chrome arm with a Ø 101 mm (4") polished stainless mirror h...

A-Ford 1930-31 Similar to our H10182  hinge mirror except this one has an offset arm. 43.18 mm is the width where it slips over the top and bottom of the hinge. Chrome arm with a Ø 101 mm (4") polished stainless mirror h...

For the 1928-29 open cars this mirror mounts in the screw hole that holds the windshield stanchion to the body. Just take the screw out and screw this in. For left side only. Fits Roadsters, Phaetons, and Roadster Pickups. Thread size is 5/16-24 O...

This mirror was used on the 30-1 Deluxe open cars. There is a flat area about half way up on the driver side stanchion where this will mount. Thread size where mirror threads into stanchion is 7/16-20 OEM: A-17683

A hinge type mirror for the Ford closed cab commercial vehicles 1928-31, Drivers side only, Mirror diameter 130 mmOEM: A-17704-A

Diameter housing, Ø 100 mm (4") Mounting: M6 with cover nut

Ford model A 1928-31 Ford Early V8 1932 Other cars with spare tire mounted in the front fender

These 3 grommets fit the headlight and horn holes in the radiator shell

These 3 grommets fit the headlight and horn holes in the radiator shell ​OEM: A-8210-BS A-Ford 1930-31

Thin rubber pads fits between headlight bar and fender. Should not be visible when installed OEM: A-13114-A