Fits 1928-1929 Model AOEM # A-18700-AStainless Steel

Fits 1930-31 Model A FordOEM # A-18700-BStainless Steel

A Ford 1931 OEM: A-18700-C Stainless Steel

A-9765

Complete Set of rubber stops for the top and bottom of the rumble lidA41484S

Square rubber pads have a good bead around outer edge. Use one between step plate & fender.A-Ford 1928-29A41563SP

Round rubber pads have a good bead around outer edge. Use one between step plate & fenderA-Ford 1930-31A41564RP

This 22 mm wide x 3.6 mtr. woven fabric welt is used as a buffer around the gas tank to eliminate rattles. The early models use it all the way around the tank; the later models on the front and back edges

This is an exact copy of a popular accessory used with accelerator by bolting onto the floorboard. Chrome pedal with rubber insert.

Authentic design. The same as the Ford design mat that came in your car when it was new. Brake to front means that the emergency brake handle is to front of gear shift lever. A-Ford 1928-29 OEM: A-2053 From the mid of 1929 the brake lever went...

These are the original, authentic design. From July 1929 till the end of production, the hand brake was to the right of the shift lever. OEM: A-2005

Much improved quality over what has been available in the past. A-Ford Tudor  1928-29 OEM: A-2055-289

Much improved quality over what has been available in the past. A-Ford Tudor 1930-31 OEM: A-2055-301

Rear Mats for the 1928 - 1931 Tudor Sedan. Old Part # A2055A or B.

A special countersunk washer used when mounting the floorboards. These washers are also used on some of the door hinges. A-Ford 1928-31 OEM: 33W and old number 109W Ring diameter: 20 x 8 mm

Special studs used to hold the floor mat in place. 4 per set

These are optional. You don't have to use them, but carpet stays in place much better with them. This is the female portion that attaches to the carpet

This metal sun visor is used on the 28-9 Coupes and Tudor Sedans. These were covered originally. Cover kit must be ordered separately

Steel - Sun Visor - Coupes, Tudors & Pickups.1930-31.A317BS

Throttle, Spark, & Accelerator cadmium plated rods with spring loaded endA-Ford 1928-31

A-Ford 1930-3171.7 cm longA9700C

Henry used a solid zinc sill plate on the Coupes and Tudors. These are authenticA46480AOR

Aluminium sill plates ford tudor  A46480AOR

Henry used a solid zinc sill plate on the Coupes and Tudors. These are authentic and much heavier than the lesser expensive aluminum plates we offer Sold as a pair Ford 1928-31 OEM: A-46480-BOR

Fits all body styles with inside vacuum or electric wipers. Provides a passenger-side wiper by running off the driver's side. This is an Accessory kit.KIT INCLUDES PAIR OF WIPER ARMS, PAIR OF BLADES, PASSENGER SIDE PIVOT SHAFT & CONNECTING LI...

2 pc gasket set for the Trico vacuum wiperA Ford 1929-31A17508G

Fits Trico KCX, KSB, and KSL motors with 1" wide bowls and snap on style covers.Includes paddle and parking seals, bowl gaskets, rivets, grease capsule, grease applicator, and instructions. A-Ford 1928-31

This line runs from the intake manifold to the fitting on the firewall.A-Ford 1928-31OEM: A17543B

Universal vacuum hose for wiper or distributer Lenght: 1.80 mtr.Inside Diameter: Ø 4 mm