Black cotton webbing with tacks goes around the floorboard to seal out air & fumes. Tack to outside edge, then fold under the board and tack again for a tight sea

This Kit seals the 2 additional wood floor pans at the rear and center on a Tudor

100 nail set

Replacement round-head bolts, with nuts & lockwashers, used in place of rivets to attach all the brackets to the frameA-Ford 1928-31OEM: A5125MB

Ford 1928-29OEM # A-8216-ACover with rivet and washer

A- Ford 1930-31Cover with rivet and washer

9.3 mm Wide, half round rubber goes on the ends and inside edge of the '31 running boards. Does both boards. Passenger Vehicle Only. OEM: A16458BR Lenght of string: 2.80 mtr about

Set of 2 rubber profiles for the running board of the A-Ford Delivery: 2 pieces Mats are pre-glued, remove protective paper and stick on. Dimensions approx: 1.17 m. x 23 cm A-Ford 1928-29 OEM: A-16455-RM

Set of 2 rubber profiles for the running board of the A-Ford Delivery: 2 pieces Mats are pre-glued, remove protective paper and stick on. A-Ford 1931 OEM: A-16455-GPM

Pair of stepplates made of aluminium and with arubber underpad.  Has hole for mouting car logo. We can supply on request several different USA made car brand logo's for these plates 

Replacement shades for the closed car.  Shade consists of shade material in the proper width with lower stick and end guides in place. Shade is attached to a new spring roller Available colors: Tan, brown or gray. Width: 66 cm.  Ot...

Shade is attached to a new spring roller, and comes with the lower stick and end guides in place. Comes with tassel in the middle of the lower pull down Color: Grey Wide: 14" (36 cm)  

A pair of chrome brackets to mount the window shade

Logo: 52 x 26 mm Bolt: Ø 6 x 25 mm ​OEM: A-16400-E

Clinch Nut used on '28 - '29 Sun Visor, Window Garnish, Cowl and Door Area Ford 1909-31

Clinch Nut used on '30 - '31 Gas Tank, Rear Sub Frame and '28 - '31 Floorboards - Trunk and Rumble

Clinch Nut used for Spare Tire Carrier on '28 - '29 Fordor Briggs and top support bar on Standard Phaetons.

3 Washer, 2 machine screws, 1 wood screw to attach pedal plate  A35122AR, A35122S or A35123BR A-Ford 1928-31

Bolt & Washer Set - Center & Rear -Authentic Black Oxide Finish - 32 Pieces - Tudor Sedan A-Ford 1928-31 OEM: A-80033-B  64.24460

Supports the front edge of the Tudor Sedan front seats. They have a 2" offset in them to give you more legroom A-Ford 1928-31 Tudor Sedan OEM: A-47902-EXT

Univeral adjustable wiper arm with hook in blade Arm: 7 1/2" arm extends to 11 1/2" ( 19 up to 29 cm) Hook and saddle style Made to clamp down on a shaft that is.235" (Ø 6 mm) in diameter. Blade: Lengt of 19 cm with stai...

This black vinyl welting is known as wire-on welt. If the original metal or aluminum moldings are not available for your car, this is what you use in place of them. You simply nail it down, then fold it over, and it will form a nice fabric beading ar...

Used to finish off the hide'm welt. (A-47304) Nickel finish. comes with a stainless steel nail. A-Ford 1928-31 OEM: A-47303-A

A set of rubber discs that go between the dash rail and the body A-Ford 1928-31 OEM: A-11900-P

The Ø 5 mm black beading for putting the fenders on. Comes in 25' roll  

1928-29 - Open Car Windshield Frame. Made from the original style round tubing. Holes drilled and tapped for the windshield stud. Holes are drilled to accept the finger pulls on the bottom tube. There are no holes driled in the top tube for the top s...

This is a clip that holds the electric wire on the open car windshield frame. For open cars only A-Ford 1928-31 OEM: A-17659

Set of 3 stainless steel carriage style bolts to attach the tail lamp bracket to the fender A-Ford 1928-31 OEM: A-13471-MBSS