Make your meal warm while you are driving with this stainless steel manifold cooker, Fits over the stock manifold of your model A

Special brush to keep the wheel spokes fresh and shiny

No longer remove the distributor.use this tool to torque the nuts that hides behind the distributor

This kit gives you everything you need except a drill bit for repairing head and manifold styd threads in the block

A2041T

A simple tool to adjust and set the model-A distributor,Complete with instructions

Handy tool for installing the new type starter drive. This will compress the drive so you can get to the mounting screw easier

A-17005

A combination device. One starter handle on one end and a wheel key at the other end

A special KR Wilson tool for easy removing of the valve guides on the model A engine

A-8501-W

Plastigage takes the guess work out of putting the proper clearance in rod and main bearings. A must when checking or adjusting bearing clearance. Toepasbaar:.001 - .003 inches.025 - .076 mm

Tape the horn button down with a piece of masking tape or have someone hold the button down for you. Now insert the light switch spider over the legs of the tool, slide the spring onto the spider and push them both onto the horn rod making sure you h...

Cast oval Ford badge,Chrome and blue backgroundSize: 75 x 37 mm x 2 mm thickSelve adhesive, No need for drilling

Hand made Ford design desk light.Base of the lamp is a hub cap of a Ford V8 from the 40's and the Halogen bulb is placed in a new old stock Ford V8 flathead piston.Switch on-off is mounted in the base.Works on 220 V with continental plug.We do have 1...

Key sizes: 1/4", 5/16", 3/8" 7/16", 1/2", 9/16" 5/8" 11/16".High quality set

This speedometer cable lubricant is a special graphite-type lube ideal for speedometers or other metal-to-metal applications such as hinges, tailgate cables, latches, regulators, lock cylinders, throttle and clutch linkages, etc Tube 14 ml. 

Door hinge pin removal tool, heavy-duty forged steel body with 7 pins

This handy tool is great for checking to see if you have spark. With the car running, just hold against the spark plug to see if you are getting spark to the plug. Not usable when a plastic or rubber cap has being placed on top of the sparkplug&nb...

Special tool for removing and installing the A-6259 cam nut

Use the bracket in this kit to determine if the flywheel is seated properly on the crankshaft. The large bracket bolts to the flywheel, then turn the flywheel so that you can be sure that the flywheel housing is correctly shimmed against the block. B...

Attaches to water inlet holes and two pan bolt holes. Lets you attach the Model A or Model T motor to a standard engine stand Round Shank is Ø 60 mm and not drilled yet

For the removal or installation of your gear shift lever spring A-Ford 1928-31  

This handy tool can be used on the front or the rear brakes of the Model A. On the rear, the tool rotates on the end of the axle housing where the roller bearing rides. When used on the front, your inner and outer bearings center the tool on the spin...

Special reamer that reams the bushings for the front spindle bolts. This reamer makes the reamed holes perfectly in line A-Ford 1928-31

Makes collapsing the valve springs a breeze! The hook hooks over the manifold stud and acts as a pivot to pry the spring upward in order to install the keeper A-Ford 1928-31

Allows you to remove the old ratchet nut without removing the radiator. Fits original size ratchet nuts which were 1-3/8" A-Ford 1928-31 OEM: A-6320

Economy Hub Puller for the 1928-31 Model A Ford with the grooved type hub. Opening at base of puller hooks into the groove on the hub. One inch bolt at end of puller must be tighten down against axle end to loosen hub from axle. Strong ductile ...

Semi-circular tool that grabs the raised shoulder of the hub to free the hub from the axle. Ductile iron.1928-31 U.S.A.