This semiconductor (state of the art) unit modernizes and replaces the original relay type of past years. It is identical to original exterior appearance and dimensions and is plated in cadmium as original. Also includes authentic insulators and hard...

This semiconductor unit modernizes with FORD script on the cover. It is identical to original exterior appearance and dimensions and is plated in cadmium as original. Also includes authentic insulators and hardware. It is designed to continuously han...

Make your old cut-out solid state by installing this diode. Can be installed in your old cut-out if it is bad. Complete with instructions. Positive ground only

Lenght 15 cm. (6 inch)A-Ford 1928-31A-10166

1928-31A-10108

You'll need to solder the wire end of this wire to the head of the bolt that goes through the casing to the Cut-out OEM: A-10102 B

A-Ford 1928-31A-10101-B

This fabric covered wire was used from Feb. of 1930 through the end of production, however it will work on all years 1928-31. This harness has the flexible black loom instead of the steel conduit that was used up to this point A-Ford:  A-1440...

This fabric covered wire was used from Feb. of 1930 through the end of production, however it will work on all years 1928-31. This harness has the flexible black loom instead of the steel conduit that was used up to this point A-Ford 1928-31 OEM:...

1928-31A-10103

All new so no core is required. This is for the early "long nose" style generator that had bearings on both ends of the armature A-Ford 1928-29 OEM: A-100005-AR

New armature, not rewound. Short nose version ( 1/2 inch nose) A-Ford 1930-31A-10005-BR

Covers the slotted holes on the A-Ford generatorA-10142-OR1928-31

A-Ford 1929-31A-10072

3 pc. brush kitA-Ford 1928-31A-10043

1930-31A-10145

A-Ford 1928-31A-10160Priced each

Flat washer that goes between the bearing and the felt washerFord 1928-31A-10114

Comes complete except for armature & field coil. Instructions included.

A-Ford 1928-316 Volt

Improve your weak generator with these good quality reproductions. 2 Pieces per Set.12 Volt systems only

Standard Cut out control6 Volt system onlyPositive earth ground

This semiconductor (state of the art) unit modernizes and replaces the original relay type of past years. It is identical to original exterior appearance and dimensions and is plated in cadmium as original. Also includes authentic insulators and hard...

6 Volt 35 Amp Unit - used on all Models A's using Halogen lights, etc. All new Alternator - not rebuilt. This is a bolt on one wire unit. Bracket and Pulley is included. Greatly increased cooling due to ducted fan and housing, also looks more lik...

12 Volt / 60 Amp Unit - used on all Models A's for most purposes. All new Alternator - not rebuilt. Increased cooling. This is a bolt on one wire unit. Bracket and Pulley is included. Greatly due to ducted fan and housing, also looks more like th...

Nieuwe 12 Volt enkel draads aansluiting wisselspannings dynamo. Deze dynamo schakelt zichzelf in bij een toerental  vanaf 800-850 tpm.  1 stroom kabel aansluiting naar de dynamo is voldoende aan/uit schakeling is automatisch dus zonder ex...

A very usefull accessory that holds the generator in place without relying strictly on the pivot bolt. Mounts using one of the existing front timing cover bolt holes. The radiused end rests against the outside of the generator or alternator. Mount...

Bracket used to mount the alternator in place of the generator. Adjusts with washers so you can shift the alternator forward or backward for belt alignment A-Ford 1928-31

A smaller diameter pulley turns the alternator 2.6 times the engine speed which allows the alternator to "turn on" quicker. Fits any Delco or Ford alternator with a .670 shaft size. "Genuine Nu-Rex." 2-1/4" O.D

This is a combination of the alternator pulley H28840 and the H-Bracket H28841 A-Ford 1928-31